Kissing Fish Mug Rug

Basic Skills Necessary:

Machine Applique

Pattern Description:

Cute idea for Valentines Day or just for a wedding or anniversary gift idea. Kissing fish and fish bowl template to make a matching pair of kissing fish mug rugs. Project by Amy at Friends Stitched Together for So Sew Easy.

For two mug rugs, or one set, you’ll need:

- The Kissing Fish Mug Rug downloadable pattern

- 1/4 yard main fabric for the fishbowl. You could use a contrast for the back if you prefer.

- Small scraps (OR 1/8 yard of fabric each) for the body, tails, lips, and fins. You can mix and match as much as you want with this – I like to use at least two different fabrics.

- 1/4 yard batting or fleece (for two 6’X6.5″ rectangles)

- 1/8 yard lightweight Heat’N’Bond

- Seam allowance is 1/2″

Cut 4 rectangles that are 6″ high and 6.5″ wide from your main fabric (or two from your front fabric and two from your backing) and two from your batting.

Trace the fish pieces onto your Heat’N’Bond. You’ll need two each of the body, tail, fin, and lips. If your fabric is directional, make sure that one set is reversed so that your fish will be mirror images. Only the fins should be the same.

Iron onto the back of your fabric scraps following the manufacturer directions and cut out.

Cut out the fishbowl from the pattern page, as shown in the picture below.

Take the front fabric rectangles and lay the fishbowl template on top. Arrange the fish pieces, minus the lips, and iron on. Make sure the fish are facing each other! I set my fish slightly closer to the side they are facing so they look like they’re on the edge of the bowl.

I originally had the small heart as a fin, but after making a happy mistake, I realized it also works as an eye! So you can flip the fin whichever way you like.

Use a satin stitch to go over the edges of the hearts. On my Singer, I set my zig zag stitch at 3.0 wide and 0.6 high. When you’re going around the curves, occasionally set your needle down on the outside of the curve, lift the foot, and rearrange the fabric a little. This will keep the curves looking smooth.

The hearts have two points. For the concave point (on the left in the below picture) you’ll want to go slightly past the edge (where the arrow is pointing), set the needle down, lift the foot and turn. For the convex point (on the right), you’ll go right to the edge of the corner, set your needle exactly at the tip of the heart (at the arrow), lift the foot and turn. This will give you nice, crisp tips.

Set your fishbowl template on the fabric again, arrange the lips, and iron them on.

Stitch over the lips, again using a satin stitch.

Use the template to draw the fishbowl shape on the wrong side of the backing fabric. I use a pen or fine-tipped Sharpie, but if you’re worried about it ruining your fabric, you can use a fabric marking pen.

Layer the three rectangles in this order: batting, fish fabric (right side up), backing fabric (wrong side up) and repeat for the other mug rug. Make sure the fish are facing the right way – that’s how my fins ended up as eyes 

Stitch on the line you drew on the backing fabric. I’m showing the batting side because it’s easier to see the stitching. Leave an opening at the bottom of the bowl, backstitching where you start and stop.

Trim the edges close to your stitching. Clip into the corners just to the stitching, but make sure you don’t cut the thread. I used pinking shears along the curves, but you could cut a series of notches instead.

Turn right side out. Use a chopstick or crochet hook to carefully push out the corners and smooth the sides. Turn the edges of the opening in and pin.

Topstitch close to the edge all the way around the bowl.

Give it a good press and you’re done! 

credits to: so-sew-easy.com