Drawstring Backpack Tutorial



We had a birthday party to go to this weekend, for a little girl turning 6. Although running to the store and grabbing something is much easier, I thought it would be fun to whip up a cute gift. I decided on this fun little drawstring backpack, and made a tutorial to go along with it.

The block in the center is made with Sherbet Pips, I bought 2 charm packs a couple months back, and the rest of the fabric are just fat quarters I had in my stash.

Inside the backpack are 2 containers of custom-made play doh, with a label… scroll down to the end of the tutorial to check it out.




What you’ll need:

- 4 charm squares or 5″ squares (2 of each design)

- 1 Fat Quarter for the border and straps (I used a stripe)

- 1 fat quarter for the lining and top (I used a pink check)

- 1 fat quarter for the back (I used white)

- General sewing supplies – scissors, sewing machine, rotary cutter, thread, etc.





Start by picking your 4 charm squares



Use a ruler to mark down the middle of two of the charm squares, diagonally. Stack one light and one dark square RST (Right Sides Together), then stitch 1/4″ on either side of the line. I used this nifty ruler that gives me my center line and my 1/4″ lines easy-peasy.



Once you’ve stitched on either side, cut down the middle, and you’ll have 4 HSTs (Half Square Triangles).



Press them open, and arrange into a pinwheel pattern. Stitch together.



Cut 5 2″ strips out of the border/strap fabric.



Cut one in half, and stitch on either side of the pinwheel bock. Use 2 other strips, stitching one to the top, and one to the bottom. Reserve the extra for the straps.



Cut the lining piece based on the size of the block. The lining will be one piece the height of the block, but twice as long. In the picture you can see that the lining is folded in half, so it is exactly the size of the block. I trimmed 1/4″ from all sides of my block to make it fit the fat quarter.

Cut the backing piece the same size as the front piece.



Cut 2 3″ wide pieces of the top/lining fabric for the casing that the drawstring will go through.



Cut the casing 1.5″ longer than your block.



Fold the small end of the casing over 1/2″, repeat, and stitch down. I did a double-layer of stitching. Repeat on both sides of the casing. Repeat for the second casing piece.



Grab the 2 extra striped fabric pieces. Attach the extra length from the border of the block, one to each. Fold in half the long way (RST) and stitch down. It will look like the picture. Turn right side out (carefully), then top stitch down each side for strength.



Fold the casing in half, and pin to the top of both the front and back pieces.



Lay these pieces down on top of the backing, add some more pins, and stitch down.



Now layer the bag exactly as it will look when it is finished, top, two middle pieces, and bottom, all with the correct sides facing the correct way.



This step is very important! Turn JUST the top piece over, so now the top piece is on the bottom, with the right side facing up, then the back with the right side down, then the lining, with the right sides facing each other.



Pin all the way around, and stitch the sides and bottom, leaving a hole at the bottom for turning.



Turn right-side out through the hole you left. Everything should come out correctly if you followed the very important step.

Thread one drawstring all the way around and pin to itself at the top. Pin the loose end at the bottom so that it forms the strap to the backpack. Stitch together at both of the pinned places. I used a small, tight zig-zag for durability.



Repeat with the other side and you have the start to a great gift!


credits to: alwaysexpectmoore.com


http://mysewingmall.com/

Comments